Skip to content
Constructeams
NYC City RecordCloses in 20 days

Bid Extension: 85625B0011-CSB General Construction RC Man. & Bronx

Location
New York, United States
Responses due
Oct 28, 2026

Overview

Department of Citywide Administrative Services (DCAS) Construction and Technical Services (CTS) is seeking a qualified vendor to provide, during the term of the Contract, the City's requirements for labor, materials, and equipment necessary to perform interior and exterior general construction work at various facilities throughout the boroughs of Manhattan and Bronx in the City of New York. EPIN 85625B0011. This solicitation is being made pursuant to the Competitive Sealed Bidding Method, Section 3-02 of the New York City Procurement Policy Board (PPB) Rules. OCP Agency 856 will have bid openings virtually via Teams. Please use the link in the Address Location box in PASSPort for the link. Pre-Bid Conference will be held virtually. Please see the Pre-Bid Conference location box in PASSPort for the link. If you are experiencing any difficulties responding to this RFx, please reach the MOCS service desk at the following link: https://mocssupport.atlassian.net/servicedesk/customer/portal/8

Source: NYC City RecordView in Constructeams

Similar open bids

SAM.govCloses today

Y1DZ--620-23-205 Mission Critical Roofs Phase II

620-23-205 Mission Critical Roofs Phase II

Montrose
Due Oct 9, 2026View bid
NYC City RecordCloses tomorrow

Requirement Contract for Installation of V/C Floor Tile in Apartments- Development Specific pursuant to RFQ's 523131,523132, 523133, 523135, 523136, 523146 -523147, located in Bronx Neighborhood (BX05) & (BX06)

No Bid Security Required. NYCHA intends to separately solicit and award a series of Seven (7) requirement contracts for Installation V/C Floor Tile in Apartments-Development Specific pursuant to RFQ#s: 523131- Adams Houses, 523132- Melrose Houses, 523133-Morrisania Air Right/Jackson Houses, 523135- St. Marys/Bronxchester Houses, 523136- Butler Houses, 523146- Morris Houses and 523147- Webster/Morrisania Houses (or this Bid Series). Contract Term: The Term of this contract shall be for a period of three (3) years from the award date established on NYCHAs Blanket Purchase Order or the issuance of the Notice to Proceed Order. NYCHA, in its sole discretion, shall have the option to extend the Term of this contract with up to two (2) one-year renewal periods. Limiting Award Provision: NYCHA has determined that it is in the best interest of NYCHA to award only one (1) of the Requirement contracts in this Bid Series to the lowest responsive, responsible individual Contractor, subject to the award limiting language (Step 1). Subject to NYCHAs responsive and responsibility determinations of the Bidder and the award limiting language set forth herein, to the extent there are other Requirement contracts in this Bid Series that are not yet awarded after Step 1, NYCHA, in its sole and absolute discretion, may award up to One (1) additional contract(s) to a Contractor or Contractors that has, pursuant to Step 1, been awarded the maximum number of contracts in this Bid Series (Step 2). Solicitations Subjected to Davis Bacon Prevailing Wage Schedule: Labor Law 220i Registration Certificates and Certification. Bidders are hereby notified that effective as of December 30, 2024, as a precondition to submitting its Bid, the Bidder and each subcontractor identified by the Bidder in its Bid, must be registered with the New York State Department of Labor (NY DOL) pursuant to Article 8, Section 220-i of the New York State Labor Law (LL 220-i). Instructions on how to register can be found at https://dol.ny.gov/contractor-and-subcontractor-landing. Current Prevailing Wage Links are posted on iSupplier under the Quick Links Section of Sourcing Supplier. The vendors are responsible for remaining informed of all updates to the Prevailing Wage Schedule. Pre-qualification: To be considered eligible for the award, a bidder must pre-qualify as an 'Approved Supplier via NYCHA-Tile Pre-Qualification List (PQL) and appear on the active approved vendor list https://www.nyc.gov/site/nycha/business/nycha-pql.page Section 3 REO & OEO Plans: Section 3 REO & OEO Plans must be submitted via eComply, https://nycha.ecomply.us/ and no later than Bid Submission Deadline. For eComply log-in assistance contact eComply Tech support: support@ecomplysolutions.com For Section 3 submissions assistance contact NYCHAs SMP Vendor Diversity team: eComply.support@nycha.nyc.gov Reminder: DO NOT include Section 3 documentation within bid submission via iSupplier Pre-Bid Conference: NYCHA hosted Pre-Bid Conferences to launch the rollout of the solicitation of the NYCHA Tile Program-Phase III/ Installation of Vinyl Composition Floor Tile in Apartments bid series. Friday, 05/29/2026*- Bronx Property Management & Bronx Developments. Friday, 06/05/2026*- Brooklyn Property Management & Brooklyn Developments. Wednesday, 06/17/2026*- Manhattan Property Management & Manhattan Developments. Wednesday, 06/24/2026*-Queens & Staten Island Property Management & Queens and Staten Island Developments. The information previously presented (*) is applicable here, hence a Pre-Bid Conference will not be hosted for this solicitation series. Questions pertaining to this Solicitation Series-RFQ#523131-523133, 523135-523136, 523146 & 523147 and submitted via the NYCHA Cyclical Procurement mailbox at: cyclical.procurement@nycha.nyc.gov (include RFQ number in subject field) prior to Question Deadline will be accepted. RFQ Question Submission Deadline: Wednesday, 09/23/2026 at 2:00PM Question and Answer Release Date: Wednesday, 09/30/2025 at 2:00PM In addition to the documents attached below, bidders are directed to review the Special Notices and Conditions, Instructions to Bidders, and General Conditions prior to submitting a bid. To access these documents, click on the 'Contract Terms' tab above, and then 'Preview Contract Terms,' to download a PDF version. Please note that in the event NYCHA receives no responses in connection with this RFQ by the original bid submission deadline, the bid submission deadline shall be extended automatically for seven (7) calendar days. The foregoing extension does not in any way limit NYCHA's right to extend the bid submission deadline for any other reason. Prior to submitting a bid, please confirm that your bid response includes all required forms & Documentation, and that all required forms and documentation are properly completed, signed, and notarized, where applicable

New York
Due Oct 9, 2026View bid
NYC City RecordCloses tomorrow

Requirement Contract for Installation of V/C Floor Tile in Apartments- Development Specific pursuant to RFQ's 523148, 523149, 523150, 528366, Located in Bronx Neighborhood (BX07)

No Bid Security Required. NYCHA intends to separately solicit and award a series of Four (4) requirement contracts for Installation V/C Floor Tile in Apartments-Development Specific pursuant to RFQ#s: 523148- Claremont Consolidated Houses, 523149- Forest Consolidated Houses, 523150-Highbridge Houses, and 528366- Sedgwick Houses (or this Bid Series). Contract Term: The Term of this contract shall be for a period of three (3) years from the award date established on NYCHAs Blanket Purchase Order or the issuance of the Notice to Proceed Order. NYCHA, in its sole discretion, shall have the option to extend the Term of this contract with up to two (2) one-year renewal periods. Limiting Award Provision: NYCHA has determined that it is in the best interest of NYCHA to award only one (1) of the Requirement contracts in this Bid Series to the lowest responsive, responsible individual Contractor, subject to the award limiting language (Step 1). Subject to NYCHAs responsive and responsibility determinations of the Bidder and the award limiting language set forth herein, to the extent there are other Requirement contracts in this Bid Series that are not yet awarded after Step 1, NYCHA, in its sole and absolute discretion, may award up to One (1) additional contract(s) to a Contractor or Contractors that has, pursuant to Step 1, been awarded the maximum number of contracts in this Bid Series (Step 2). Solicitations Subjected to Davis Bacon Prevailing Wage Schedule: Labor Law 220i Registration Certificates and Certification Bidders are hereby notified that effective as of December 30, 2024, as a precondition to submitting its Bid, the Bidder and each subcontractor identified by the Bidder in its Bid, must be registered with the New York State Department of Labor (NY DOL) pursuant to Article 8, Section 220-i of the New York State Labor Law (LL 220-i). Instructions on how to register can be found at https://dol.ny.gov/contractor-and-subcontractor-landing. Current Prevailing Wage Links are posted on iSupplier under the Quick Links Section of Sourcing Supplier. The vendors are responsible for remaining informed of all updates to the Prevailing Wage Schedule. Pre-qualification: To be considered eligible for the award, a bidder must pre-qualify as an 'Approved Supplier via NYCHA-Tile Pre-Qualification List (PQL) and appear on the active approved vendor list https://www.nyc.gov/site/nycha/business/nycha-pql.page Section 3 REO & OEO Plans: Section 3 REO & OEO Plans must be submitted via eComply, https://nycha.ecomply.us/ and no later than Bid Submission Deadline. For eComply log-in assistance contact eComply Tech support: support@ecomplysolutions.com For Section 3 submissions assistance contact NYCHAs SMP Vendor Diversity team: eComply.support@nycha.nyc.gov Reminder: DO NOT include Section 3 documentation within bid submission via iSupplier. Pre-Bid Conference: NYCHA hosted Pre-Bid Conferences to launch the rollout of the solicitation of the NYCHA Tile Program-Phase III/ Installation of Vinyl Composition Floor Tile in Apartments bid series.  Friday, 05/29/2026*- Bronx Property Management & Bronx Developments.  Friday, 06/05/2026*- Brooklyn Property Management & Brooklyn Developments.  Wednesday, 06/17/2026*- Manhattan Property Management & Manhattan Developments.  Wednesday, 06/24/2026*-Queens& Staten Island Property Management & Queens and Staten Island Developments. The information previously presented (*) is applicable here, hence a Pre-Bid Conference will not be hosted for this solicitation series. Questions pertaining to this Solicitation Series-RFQ#523148-523150, 528366 and submitted via the NYCHA Cyclical Procurement mailbox at: cyclical.procurement@nycha.nyc.gov (include RFQ number in subject field) prior to Question Deadline will be accepted. RFQ Question Submission Deadline: Wednesday, 09/23/2026 at 2:00PM Question and Answer Release Date: Wednesday, 09/30/2025 at 2:00PM In addition to the documents attached below, bidders are directed to review the Special Notices and Conditions, Instructions to Bidders, and General Conditions prior to submitting a bid. To access these documents, click on the 'Contract Terms' tab above, and then 'Preview Contract Terms,' to download a PDF version. Please note that in the event NYCHA receives no responses in connection with this RFQ by the original bid submission deadline, the bid submission deadline shall be extended automatically for seven (7) calendar days. The foregoing extension does not in any way limit NYCHA's right to extend the bid submission deadline for any other reason. Prior to submitting a bid, please confirm that your bid response includes all required forms & Documentation, and that all required forms and documentation are properly completed, signed, and notarized, where applicable.

New York
Due Oct 9, 2026View bid
NYC City RecordCloses tomorrow

Requirement Contract for Installation of V/C Floor Tile in Apartments- Development Specific pursuant to RFQ: 528367- Clason Point Houses, Located in Bronx Neighborhood (BX03).

No Bid Security Required. NYCHA intends to separately solicit and award a series of One (1) requirement contracts for Installation V/C Floor Tile in Apartments-Development Specific pursuant to RFQ#s: 528367- Clason Point Houses, (or this Bid Series). Contract Term: The Term of this contract shall be for a period of three (3) years from the award date established on NYCHAs Blanket Purchase Order or the issuance of the Notice to Proceed Order. NYCHA, in its sole discretion, shall have the option to extend the Term of this contract with up to two (2) one-year renewal periods. Limiting Award Provision: NYCHA has determined that it is in the best interest of NYCHA to award only one (1) of the Requirement contracts in this Bid Series to the lowest responsive, responsible individual Contractor, subject to the award limiting language (Step 1). Subject to NYCHAs responsive and responsibility determinations of the Bidder and the award limiting language set forth herein, to the extent there are other Requirement contracts in this Bid Series that are not yet awarded after Step 1, NYCHA, in its sole and absolute discretion, may award up to One (1) additional contract(s) to a Contractor or Contractors that has, pursuant to Step 1, been awarded the maximum number of contracts in this Bid Series (Step 2). Solicitations Subjected to Davis Bacon Prevailing Wage Schedule: Labor Law 220i Registration Certificates and Certification Bidders are hereby notified that effective as of December 30, 2024, as a precondition to submitting its Bid, the Bidder and each subcontractor identified by the Bidder in its Bid, must be registered with the New York State Department of Labor (NY DOL) pursuant to Article 8, Section 220-i of the New York State Labor Law (LL 220-i). Instructions on how to register can be found at https://dol.ny.gov/contractor-and-subcontractor-landing. Current Prevailing Wage Links are posted on iSupplier under the Quick Links Section of Sourcing Supplier. The vendors are responsible for remaining informed of all updates to the Prevailing Wage Schedule. Pre-qualification: To be considered eligible for the award, a bidder must pre-qualify as an 'Approved Supplier via NYCHA-Tile Pre-Qualification List (PQL) and appear on the active approved vendor list https://www.nyc.gov/site/nycha/business/nycha-pql.page Section 3 REO & OEO Plans: Section 3 REO & OEO Plans must be submitted via eComply, https://nycha.ecomply.us/ and no later than Bid Submission Deadline. For eComply log-in assistance contact eComply Tech support: support@ecomplysolutions.com For Section 3 submissions assistance contact NYCHAs SMP Vendor Diversity team: eComply.support@nycha.nyc.gov Reminder: DO NOT include Section 3 documentation within bid submission via iSupplier. Pre-Bid Conference: NYCHA hosted Pre-Bid Conferences to launch the rollout of the solicitation of the NYCHA Tile Program-Phase III/ Installation of Vinyl Composition Floor Tile in Apartments bid series.  Friday, 05/29/2026*- Bronx Property Management & Bronx Developments  Friday, 06/05/2026*- Brooklyn Property Management & Brooklyn Developments  Wednesday, 06/17/2026*- Manhattan Property Management & Manhattan Developments  Wednesday, 06/24/2026*-Queens& Staten Island Property Management & Queens and Staten Island Developments. The information previously presented (*) is applicable here, hence a Pre-Bid Conference will not be hosted for this solicitation series. Questions pertaining to this Solicitation Series-RFQ#528367 and submitted via the NYCHA Cyclical Procurement mailbox at: cyclical.procurement@nycha.nyc.gov (include RFQ number in subject field) prior to Question Deadline will be accepted. RFQ Question Submission Deadline: Wednesday, 09/23/2026 at 2:00PM Question and Answer Release Date: Wednesday, 09/30/2025 at 2:00PM In addition to the documents attached below, bidders are directed to review the Special Notices and Conditions, Instructions to Bidders, and General Conditions prior to submitting a bid. To access these documents, click on the 'Contract Terms' tab above, and then 'Preview Contract Terms,' to download a PDF version. Please note that in the event NYCHA receives no responses in connection with this RFQ by the original bid submission deadline, the bid submission deadline shall be extended automatically for seven (7) calendar days. The foregoing extension does not in any way limit NYCHA's right to extend the bid submission deadline for any other reason. Prior to submitting a bid, please confirm that your bid response includes all required forms & Documentation, and that all required forms and documentation are properly completed, signed, and notarized, where applicable.

New York
Due Oct 9, 2026View bid
NYC City RecordCloses tomorrow

84125P0014-ESA, Roadway Eng, Data Coll, Design, Inspect & Related Srvs

The Roadway Repair & Maintenance (RRM) division of the Department of Transportation is seeking appropriately qualified vendors to provide Roadway Engineering, Data Collection, Design, Inspection, and Related Services to assist the Department in its daily workflow and to assist in the development of projects to improve roadway pavement and drainage, to conduct studies to allow the initiation of capital projects to improve elements of the limited access arterial system; to evaluate materials and equipment proposed for Agency use; to support DOT facilities environmental and legal compliance; and other purposes as exemplified in the typlical tasks. This Procurement is subject to participation goals for New York States Disadvantaged Business Enterprise (DBE) as required by FHWA; however, there is no DBE goal set for this project. A Pre-Proposal Conference has been scheduled for September 17, 2026, at 10:00 AM through the Microsoft Teams link. Proposers who wish to attend the Conference meeting can access it by using the Link provided in the 'Prepare RFX' Section - SETUP Tab - Pre-Proposal/Pre-Bid Conference Section in PASSPort. This Request for Proposals (RFP) is released through PASSPort, New York City's online procurement portal. Responses to this RFP must be submitted via PASSPort. To access the RFP, vendors should visit the PASSPort public Portal at https://a0333-passportpublic.nyc.gov/rfx.html Read the DISCLAIMER and Click on LOG IN link provided within the DISCLAIMER instructions to respond to a Released solicitation (RFx), Log in to PASSPort, go to the RFx tab, and choose Browse My RFx Responses or Browse Public RFx to locate the RFx to which you are looking to respond. Enter the EPIN or Procurement Name in the keywords search to find the RFx. Then, click the pencil icon next to the procurement Name of the RFx you are interested in viewing

New York
Due Oct 9, 2026View bid
SAM.govCloses today

KB Duct List

Salient Characteristics SpecificationTitle: Galvanized Steel Quick-Disconnect Ductwork and Components for Air-Conditioning SystemSubject: Supply of modular galvanized steel quick-disconnect ductwork, fittings, dampers, and support hangers.Basis of Design: The part numbers below are for reference and configuration cross-reference. Products offered may be from another acceptable manufacturer, provided they meet or exceed all salient characteristics and are fully compatible with the complete ductwork system.1. Scope and PurposeThis requirement is for the supply and delivery only of galvanized steel, modular quick-disconnect ductwork and associated fittings for an air-conditioning system. The supplied components shall form a mutually compatible duct system consisting of straight duct sections, reducers, wye connectors, elbows, airflow dampers, and saddle hangers.Installation, field fabrication, field welding, and connection to existing equipment are not included unless specifically added elsewhere in the solicitation.2. General Salient Characteristics. All offered items shall meet the following minimum requirements: Material: Items 1 through 26 shall be galvanized steel only. No stainless steel, aluminum, plastic, or uncoated carbon-steel substitutes shall be accepted.System Compatibility: All duct, fittings, dampers, and hangers shall be compatible with the specified quick-disconnect duct system. Components of the same nominal duct diameter shall connect directly without adapters, field welding, rivets, sheet-metal screws, or permanent field modification.Quick-Disconnect Connection: Straight duct sections, reducers, wye connectors, elbows, tees, and dampers shall use a quick-disconnect connection configuration compatible with the remaining supplied components. Connection features shall permit assembly and disassembly of the duct system without damage to the duct or fittings.Nominal Dimensions: Duct diameters and fitting dimensions listed in the schedule are nominal inside diameters unless the manufacturer???s standard quick-disconnect system identifies dimensions differently. Reducers shall transition between the listed inlet and outlet diameters. Fittings shall be sized to directly mate with the corresponding duct diameter.Gauge Requirements: Straight duct sections and dampers shall be 20-gauge galvanized steel where identified in the schedule. Reducers, elbows, wye connectors, tees, and 90-degree fittings shall be 18-gauge galvanized steel where identified in the schedule. Saddle hangers shall be 14-gauge galvanized steel where identified in the schedule.Quality and Condition: Products shall be new, free of corrosion, dents, sharp edges, cracks, deformation, damaged coating, or manufacturing defects that would prevent proper assembly or service. Duct sections shall be round, and fittings shall retain their intended shape to allow proper connection. Components shall be packaged and shipped to prevent damage or distortion in transit.Equal Products: An offered equal product shall meet every listed dimensional material, gauge, connection, configuration, and quantity requirement. The offeror shall provide manufacturer specifications or product literature sufficient to verify compliance when requested.3. Required Items ScheduleItem. Required Item / Salient Characteristics. Minimum Material / Gauge. Qty. Reference No.*1. Quick-disconnect straight duct, nominal 24-inch diameter. Galvanized steel, 20 ga 17 EA 10024.2. Quick-disconnect reducer, 24-inch inlet to 22-inch outlet Galvanized steel, 18 ga 5 EA 16024.3. Quick-disconnect straight duct, nominal 22-inch diameter Galvanized steel, 20 ga 20 EA 10022.4. Quick-disconnect reducer, 22-inch inlet to 20-inch outlet Galvanized steel, 18 ga 5 EA 16022.5. Quick-disconnect straight duct, nominal 20-inch diameter Galvanized steel, 20 ga 17 EA 10020.6. Quick-disconnect reducer, 20-inch inlet to 18-inch outlet Galvanized steel, 18 ga 5 EA 16020.7. Quick-disconnect 45-degree wye connector, nominal 24-inch duct size Galvanized steel, 18 ga 1 EA 14224.45.8. Quick-disconnect 45-degree elbow, nominal 22-inch duct size Galvanized steel, 18 ga 1 EA 12022.45.9. Quick-disconnect manual butterfly valve airflow damper, nominal 22-inch duct size Galvanized steel, 20 ga 1 EA 19422.10. Quick-disconnect straight duct, nominal 18-inch diameter Galvanized steel, 20 ga 28 EA 10018.11. Quick-disconnect tee, 18-inch ?? 18-inch ?? 18-inch Galvanized steel, 18 ga 1 EA 14318.12. Quick-disconnect straight duct, nominal 16-inch diameter Galvanized steel, 20 ga 19 EA 10016.13. Quick-disconnect reducer, 18-inch inlet to 16-inch outlet Galvanized steel, 18 ga 3 EA 16018.14. Quick-disconnect 45-degree elbow, nominal 16-inch duct size Galvanized steel, 18 ga 2 EA 12016.45.15. Quick-disconnect manual butterfly valve airflow damper, nominal 16-inch duct size Galvanized steel, 20 ga 2 EA 19416.16. Quick-disconnect 90-degree elbow, nominal 20-inch duct size Galvanized steel, 18 ga 2 EA 12020.90.17. Saddle hanger sized for nominal 24-inch duct Galvanized steel, 14 ga 14 EA 17024.18. Saddle hanger sized for nominal 22-inch duct Galvanized steel, 14 ga 14 EA 17022.19. Saddle hanger sized for nominal 20-inch duct Galvanized steel, 14 ga 14 EA 17020.22. 16-inch galvanized clamp with white nitrile gasket, 27 EA 13016-GA-N.23. 18-inch galvanized clamp with white nitrile gasket, 30 EA 13018-GA-N.24. 20-inch galvanized clamp with white nitrile gasket, 25 EA 13020-GA-N.25. 22-inch galvanized clamp with white nitrile gasket, 28 EA 13022-GA-N.26. 24-inch galvanized clamp with white nitrile gasket, 24 EA 13024-GA-N.*Reference numbers are not brand-name requirements and are included only to identify the intended configuration and compatibility standard. Galvanized Ducting shall be Standard 5-feet Lengths and 11-inch Galvanized Standard Adjustable Sleeves where applicable.4. Component-Specific Requirements shall be galvanized steel:4.1 Saddle Hangers (items 17-21) used for handing duct systems and reducing sway Shall be nominal 24-inch diameter 14 ga 14 EA 17024, 22-inch diameter 14 ga 14 EA 17022, 20-inch diameter 14 ga 14 EA 17020, 18-inch diameter 14 ga 18 EA 17018, or 16-inch diameter 14 ga 14 EA 17016, as identified in the item schedule. Shall use the required quick-disconnect end configuration.4.2 Reducers Shall be galvanized steel, 18 gauge. Shall provide the listed nominal transitions: 24 x 22 inches, 22 x 20 inches, 20 x 18 inches, and 18 x 16 inches. Shall have quick-disconnect ends compatible with the adjoining duct sections.4.3 Elbows, Wye Connector, and Tee, shall be galvanized steel, 18 gauge. Shall have the listed nominal diameter and directional configuration. The wye connector and applicable elbows shall be 45 degrees as listed. The 20-inch elbow shall be 90 degrees. The tee shall be 18 inches ?? 18 inches ?? 18 inches. All ends shall be compatible with the required quick-disconnect duct system.4.4 Airflow Dampers Shall be galvanized steel, 20 gauge. Shall be sized for 22-inch or 16-inch nominal quick-disconnect duct, as identified in the item schedule. Shall be suitable for controlling airflow within the compatible duct system. 4.5 Saddle Hangers Shall be galvanized steel, 14 gauge. Shall be contoured and sized to support the corresponding nominal duct diameter without crushing, deforming, or damaging the duct. Shall be suitable for attachment to the Government???s selected overhead support method. 5. Inspection and Acceptance the Government may inspect delivered items for: Correct item type, nominal size, gauge, and quantity; Galvanized-steel construction; Compatibility of quick-disconnect connections among offered components; Required elbow, wye, tee, reducer, damper, and hanger configurations; Damage, deformation, corrosion, or deficient protective packaging; and Manufacturer literature or other documentation supporting compliance with the salient characteristics. Items that do not meet the stated requirements may be rejected.

United States
Due Oct 8, 2026View bid